What are seam allowances? Keep reading to find out more…
Before we dive in too deep into the pattern making fundamentals series, let’s first discuss seam allowances.
Seam allowances
Seam allowance is the excess fabric that you see on the inside seams of a garment. Basically, it is the amount of fabric allowed for a joining different parts of a garment together. A seam allowance needs to be added all the way around a pattern piece, except any part of the pattern that is to be cut on the fold.
Seam allowances fall in the area between the pattern edge and the stitching line. They vary quite a bit and can range anywhere from ⅛″ wide to as much as several inches.
Keep in mind that industry seam allowances are very different from commercial sewing patterns intended for the home sewist. Let’s take a closer look…
Is there a standard seam allowance?
Well, yes and no. Standard seam allowances for commercial store bought patterns tend to be ⅝″ of an inch*. Most home sewing machine cover plates will have a guide line clearly marked at this distance (from the needle) as well as other various measurements. Using the guide on the cover plate helps to ensure that the edge of the fabric is lined up while sewing so that the needle stitches the seam at ⅝″ of an inch from the fabrics edge, creating the perfect (and intended) seam allowance.
On the other hand, industry seam allowances are drastically different. But, why? Well, it’s the equipment! A variety of industrial machines are used in the mass production of apparel. Frankly, most of us do not have industrial equipment in our homes…and since this website is dedicated to practical pattern making for the home sewist…we will mostly focus on what makes sense for us using home sewing equipment. So, if your goal is to become an industry professional (read snob)…then this site is not for you! All jokes aside…adding seam allowance to patterns in the home setting can also come down to preference!
*As discussed below, different areas of a pattern piece will use different seam allowance. There is a very good reason for this, keep reading!
Pro Tip: When pattern making it is always important to draft your patterns sans seam allowance. However, after all fittings and alterations are complete and when transfering the final pattern…you will then add your seam allowances and hems.
So, when do seam allowances vary?
Although you’ll find it somewhat depends on the preference of the home sewist, the style and fabric, or the commercial pattern company, here are some common variations in seam allowances.
⅛″
- Bound shirt sleeve vents, often used in conjunction with cuffs
- Plackets
Why?
⅛″ is used in this instances because a placket, for example, is very narrow. Usually an inch or so…If a larger seam allowance were used, there would be way to much excess bulk fabric and fabric would need to be trimmed away. So, save yourself the trouble and use the smallest seam allowance possible!
¼″
- Tight curves such as scallops
- All outside edges, like cuffs
- Necklines and Collars
- Welt Pockets
- All faced areas
- Sleeveless armholes
- Narrow spacing
Why?
¼″ is used for for things such as collars for a very similar reason as stated above…But, also because it’s easier and more accurate to sew a curve with a smaller seam allowance.
⅜″-½″-⅝″
- General seaming ie. shoulder seams, side seams, waist seams, armholes, sleeve seams, inseams, cuffs, waistbands, princess lines, patch pocket (turn under), and almost anything else you can think of!
Why? And why the range?
Here’s the deal….as I mentioned above, this website is about being practical and about pattern making in the home setting. . . So, honestly…It’s going to be up to you! Personally, I hate using ⅝″ like most commercial sewing patterns. I just hate it! I find it bulky and cumbersome. Whereas, I find ⅜″ to be little too small for my liking…so, my sweet spot is ½″! I also like ½″ because it’s super easy to add with a clear plastic ruler.
Other types of seam allowances…the exceptions to the nonexistent rule.
Just to complicate something as seamingly as simple as seam allowance…let’s look at different seam classes…Yes, seams can be categorized!
Okay…so, let’s talk about hems. A hem typically has two turns. I said typically, of course there are exceptions….But, I digress…a hem will have a different amount of seam allowance depending on what type of garment is being drafted.
For example, a floor length ball gown might have 2″-4″ of hem depending on the fabric…..This not only creates weight and a nice swing in the sweep…but, it also allows for alterations in length. How about a pencil skirt. You might allow 1 ¼″ (¼″ first turn and 1″ second turn). Again, it’s totally up to the style of the garment and the fabric being used!
Lastly, there are also other things…like stuff you might attach to a garment. Like a zipper or a patch pocket. All of these will vary depending on the width of the zipper tape, the type of pocket. etc. All exceptions to the nonexistent rule!
Stay Tuned, in a follow up post…I’ll show you how to add seam allowance!
Leave a Reply